#Seagate freeagent dockstar debian full version
#Seagate freeagent dockstar debian install
#Seagate freeagent dockstar debian update

The front LED does not work other then blinking green while uBoot is loading. pdns-recursor versions 3.1.7.2 and 3.2 use the function “swapcontext” which is not supported by glibc (version 2.11.2-r3 and most likely not any other version either) on arm. If, for some reason, you want recursive DNS use unbound (version 1.4.3 worked for me). If you want PHP, go with 5.3.3 or greater otherwise you may get Segmentation Faults. Kernel Modules):Īnd followed the rest of the handbook until the end.įail2Ban-0.8.4-r2, Shorewall-Perl-4.2.11.1 and Nut-2.4.3-r2 all installed and ran just fine even though they were masked by “missing keyword” If you have any kernel modules I recommend you “make modules”. Note: I didn’t use vanilla-sources, I used gentoo-sources I followed just the instructions for “ 5. Make sure you add the swap file to fstab so that it gets used otherwise you will get compile failures when the dockstar runs out of memory. Instead of a swap partition, I made a 1GB swap file like this:ĭd if=/dev/zero of=/mnt/gentoo/.swapfile count=2M Liked: Simple setup, Expandable storage (up to four USB drives), Affordable Disliked: Requires yearly subscription for Pogoplug. I made the whole drive one big ext3 partition because I suspected that the uBoot bootloader that I used wouldn’t accept more then one partition. Seagate FreeAgent DockStar STDSA10G-RK reviews, pros and cons. Make sure you run the command to tell it you want to use ext3 for you boot partition. The hardware I used was a Seagate Dockstar model# STDSA10G-RK with an external FreeAgent Go hard disk model# ST903203FGA2E1-RKĪnd followed everything up to “ Things To Do After First Boot“.

#Seagate freeagent dockstar debian full version

If I have time at some point I intend on posting a more full version so this “guide” does not have to rely on someone else’s “guide” that may not be there later.ĭISCLAIMER: This site and any of it’s admins/moderators/staff and myself cannot be held responsible if anyone follows this “guide” and damages or “ bricks” their dockstar (or damages anything else) while using, in full or in part, the information presented here. What does “short version” mean? It means that it just points to the relevant bits of the relevant guides that I followed to make it work.

#Seagate freeagent dockstar debian update

When make upgrade of uboot, is need re-write arg of machine id!!Īll users that use uboot.gz will to have update own machine id.This is just the short version of what I did to put gentoo on a Seagate Dockstar. Hardware : Marvell eSATA SheevaPlug Reference BoardĠ0000690 Marvell DB-88F6281-BP Development BoardĠ0000691 Marvell RD-88F6192-NAS Development BoardĠ0000692 Marvell RD-88F6281 Reference BoardĠ0000a76 Marvell eSATA SheevaPlug Reference BoardĠ0000831 Marvell SheevaPlug Reference BoardĠ0000a63 Marvell GuruPlug Reference BoardĠ0000fb6 ZyXEL NSA310 1-Bay Power Media ServerĠ0000f74 ZyXEL NSA320 2-Bay Power Media Server Processor : Feroceon 88FR131 rev 1 (v5l ) Linux OpenWrt 3.3.8 #1 Sun Mar 24 01:42: armv5tel cat /proc/cpuinfo PID hash table entries: 512 (order: -1, 2048 bytes uname -a Kernel command line: console =ttyS0,115200 mtdparts =orion_nand:1M (u-boot (second_stage_u-boot (kernel (rootfs ) rw root =/dev/mtdblock3 rw rootfstype =jffs2 Built 1 zonelists in Zone order, mobility grouping on. Memory policy: ECC disabled, Data cache writeback

Machine: Marvell eSATA SheevaPlug Reference Board CPU: VIVT data cache, VIVT instruction cache When using DockStar, users will be sharing. I see several references to Pogoplug in conjunction with FreeAgent DockStar why Seagate Technology has partnered with Pogoplug to bring you the FreeAgent DockStar. Start your plug computer and a few seconds later you should be able to connect to /dev/ttyUSB1 with 115200 baud.

#Seagate freeagent dockstar debian install

Linux version 3.3.8 ) (gcc version 4.6.3 20120201 (prerelease ) (Linaro GCC 4.6-2012.02 ) ) #1 Sun Mar 24 01:42: Frequently asked questions for FreeAgent DockStar drives, including information on usage, supported file formats, and connections. Seagate FreeAgent DockStar: uImage and uInitrd Now connect the install medium (USB stick, SD card or eSATA disk) to your plug computer and connect a mini-USB connector in order to access the serial console. Image Type: ARM Linux Kernel Image (uncompressed ) # Booting kernel from Legacy Image at 06400000. When kernel is loading it recognize as Marvell eSATA SheevaPlug Reference Board. I have installed openwrt on segate GoFlex Net following openwrt wiki.įor to have sata support i installed uboot kwb-2011.12-goflexnet-L2Coff-IDEpatched.įrom uboot log appear that uboot kwb-2011.12 recognize correctly devices.Īrm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1